Skip to content
72 models · cut to your exact screen
Protecterr
Under 2 minutesNo tools neededNo trim removal

How to install your screen protector

Easier than a phone protector — the surface is bigger, flatter and there is no curved edge to fight. The only thing that separates a perfect install from a frustrating one is dust control, so most of this guide is about that.

Before you start

Three minutes of prep saves the install

Everything below is about controlling dust and temperature. Get these right and the rest is mechanical.

  • Park in shade, cool the panel

    A dashboard in direct sun can pass 60°C. Adhesive grabs too fast on hot glass and you lose your alignment window. Wait until the panel is cool to the touch.

  • Kill the airflow

    Turn the AC off or point the vents away from the dash. Moving air across a freshly cleaned screen is the fastest way to land new dust on it.

  • Wash your hands, work indoors if you can

    Skin oil on the adhesive side leaves a permanent mark. A garage or covered parking beats a driveway on a windy day.

The install

Four steps, about two minutes

Everything you need is in the box: protecterr screen protector, wet wipe, dry wipe, dust sticker, squeegee, installation guide.

  1. Clean

    Park in shade and let the dashboard cool. Wipe the display with the wet wipe, working outwards from the centre so you push dirt off the panel rather than around it.

    Cool glass first — adhesive misbehaves on a hot dash.

  2. Dry & de-dust

    Buff dry with the dry wipe, then lift every remaining speck with the dust sticker. Hold the screen at an angle to the light — that is the only way to see the fine dust that ruins an install.

    Angle the screen to a light source. Dust hides head-on.

  3. Align

    Peel about a third of the backing. Rest the protector against the top edge of the display and line up the corners before any adhesive touches the glass. Take your time here — this is the step that decides the result.

    Align dry first. You get one clean landing.

  4. Lay & squeegee

    Lower it slowly while pulling the rest of the backing away. Sweep the squeegee from the centre outwards to push air to the edges. Small bubbles clear themselves within a day as the adhesive settles.

    Trapped a bubble? A dust speck is under it — lift that corner.

Avoid these

Six mistakes that ruin an otherwise good install

Every one of these comes from real support messages. None of them are obvious the first time.

  • Fitting it on a hot dashboard

    Park in shade and let the panel cool to touch temperature

    Warm adhesive grabs before you have finished aligning, and warm glass off-gasses moisture that shows as haze under the film for the first day.

  • Cleaning with a household glass spray

    Use only the wet wipe supplied in the kit

    Ammonia-based cleaners attack the factory anti-glare coating, and any residue stops the adhesive bonding evenly.

  • Checking for dust head-on

    Angle the screen against a light source

    Fine dust is invisible when you look straight at a dark screen. Tilt it until light rakes across the surface and every speck shows up.

  • Peeling the whole backing off at once

    Peel about a third, align, then pull the rest as you lay it down

    A fully exposed adhesive face attracts airborne dust in seconds and gives you no chance to correct alignment.

  • Pressing hard to push out a stubborn bubble

    Lift that corner, remove the speck, lay it back down

    A bubble that will not move has something solid under it. Pressing harder just polishes the dust into the factory screen.

  • Installing with the engine running and AC on full

    Switch the vents away from the dashboard

    Airflow across the panel is the fastest way to blow new dust onto a freshly cleaned surface.

Troubleshooting

Install questions, answered

Not bought yours yet? Find the cut for your car, then come back to this page when the box arrives.

Shop on AmazonFind my car

You can use it immediately. The adhesive keeps curing for about 24 hours, which is also when any remaining micro-bubbles disappear on their own.

Yes, if they are small and evenly scattered — those are air pockets and they self-clear within a day as the silicone adhesive settles. A single larger bubble that will not move has a dust speck under it and needs the lift-and-clean fix.

Yes. Lift slowly from one corner, keeping the film as flat as you can, and lay it down again. Reposition on the same day if possible — the longer the adhesive has settled, the more likely it is to pick up dust during a lift.

No. The protector sits on the outside of the display glass. Nothing is disassembled, no clips are released, and nothing about the installation affects your vehicle warranty.

Yes — treat it exactly as you would the bare screen. A dry microfibre for daily dust, a slightly damp one for anything stubborn. Avoid ammonia-based cleaners, solvents and abrasive pads, same as with the factory panel.

Lift a corner with a fingernail or a plastic card and peel slowly at a shallow angle. The silicone adhesive comes away cleanly with no residue. Clean the screen before fitting the replacement.